Home Automotive Best Floor Jacks for the Toyota Tacoma (Jack Points & Gen-by-Gen Fit)

Best Floor Jacks for the Toyota Tacoma (Jack Points & Gen-by-Gen Fit)

If you are shopping for the best floor jack for a Toyota Tacoma, the honest answer is the Performance Tool W1645 — and the reason has nothing to do with tonnage. A Tacoma is a mid-size truck, and even the heaviest one Toyota builds does not come close to loading a 2-ton jack when you lift one end. What catches people out is height: a stock Tacoma sits about 9.4 inches off the ground, and put it on 33s and the cheap jack in your cart runs out of travel before the tyre leaves the floor. Below are the three jacks and one set of stands I would buy for a Tacoma, plus where Toyota says to put them.

As an Amazon Associate, Top10Great earns from qualifying purchases. This post contains affiliate links, which means we may receive a commission if you buy through our links, at no extra cost to you.

Quick comparison

Jack Best for Key spec Price Link
Performance Tool W1645 Best overall 3.5-ton, 3.5″–20.5″ lift, dual piston $$ Check price
BIG RED T83006 Torin Best budget 3-ton trolley, ~20.9″ with extra saddle $$ Check price
Arcan A20019 (ALJ3T) Best premium 3-ton aluminium, ~56 lb, 3.75″–18″ $$$ Check price
BIG RED T46002A stands The stands Pair, double locking, 15.4″–23.8″ $ Check price

Tacoma jack points: where Toyota actually says to lift

Start here: the wrong jack in the right place beats the right jack in the wrong place. The Tacoma service manual gives two floor-jack positions:

  • Front: the centre of the crossmember.
  • Rear: the centre of the rear differential.

The complication is the skid plate. If your truck has the OEM or TRD front skid plate you are not looking at bare crossmember, but at a small protrusion — which Tacoma owners universally call “the nipple” — poking through the rear of the plate. That is the jack point. One owner on TacomaWorld pulled his skid plate off specifically to check what was behind it and reported finding, in his words, a sturdy crossmember. You do not need to remove the plate to use it.

For stands, put the front pair on the frame rails just ahead of the transmission crossmember. At the rear, go under the axle rather than the body. There is a real split in the forums here: some owners set the rear stands at the centre pumpkin, others just inboard of the U-bolt plates. Both hold; the U-bolt position is marginally better, loading the axle tube rather than the cast housing.

Three warnings straight from owners who learned them the hard way:

  • There is a small drain-plug-like extrusion on the underside of the pan. Do not put the jack pad on it — use a rubber cup or folded microfiber over the saddle.
  • If your stands have castellated tops, seat the differential in the round valley and the frame rail between the peaks, never balanced on a peak. The Tacoma’s front frame points are close to flat, so nothing nests there the way it does at the diff — confirm the stand is square before you let the jack down.
  • Some owners lift from the end of the front lower control arm. It works, but you cannot get a stand under it afterwards, which makes it a tyre-swap trick rather than a way to get under the truck.

Why a 3 ton floor jack for a Tacoma is about height, not capacity

Here is the arithmetic nobody on page one bothers with. The lightest 2024 Tacoma, an XtraCab SR, has a curb weight of 4,145 lb. The heaviest, a Double Cab Trailhunter, is 5,410 lb, with the i-FORCE MAX hybrid trims between 5,030 and 5,170 lb. Earlier trucks are lighter. Lifting one end of a vehicle picks up roughly 55 to 60 percent of its weight, so the worst case at the jack is about 3,250 lb.

A 2-ton jack is rated at 4,000 lb, so on paper it covers every Tacoma ever built. That is where the Tacoma differs sharply from a full-size truck, where the load maths genuinely pushes you to three tons. Buy three tons anyway, but buy it for the reason that matters: those jacks sit on longer chassis with taller lift arcs.

How much height? On a stock Tacoma, 16 to 17 inches of maximum lift gets a front wheel clear when you jack from the crossmember. Add a 2 to 3 inch lift and 33s and you want 19 minimum — which eliminates most of the bargain jacks on Amazon, as they stop between 13 and 15. The flip side: you do not need an extreme low-profile jack. A 3.5 inch saddle rolls under a Tacoma rocker with inches to spare, and a 2.75 inch racing jack costs you top-end travel you do need. If your truck is lifted beyond any trolley jack’s reach, the forum answer is a bottle jack with an integrated locking stand, not blocking up a floor jack.

Generation by generation

2nd gen, 2005–2015. The lightest modern Tacoma and the one most likely to have a rusty frame in the salt states. Before you trust a frame rail with a stand, press a screwdriver into it. If it goes in, the jack is not your problem.

3rd gen, 2016–2023. The generation most forum discussion is about, and where the skid-plate question comes up constantly. Crossmember front, diff rear, stands on the frame rails ahead of the transmission crossmember.

4th gen, 2024 onward. Heavier across the board, and the i-FORCE MAX trims carry a hybrid battery that shifts weight rearward. Lift points are unchanged, but the Trailhunter at 5,410 lb is the heaviest Tacoma yet and sits higher from the factory. Buying for a Trailhunter or TRD Pro? Treat 19 inches of lift as a hard minimum.

The best floor jack for Toyota Tacoma owners: 3 picks

1. Performance Tool W1645 — best overall

A 3.5-ton steel service jack with a dual-pump piston and a swivelling saddle. It wins on one number: 20.5 inches of lift, more than a lifted Tacoma on 33s needs and as much as anything in this bracket.

  • 20.5 inch maximum lift clears a 3-inch-lifted Tacoma without topping out mid-stroke.
  • Dual pistons reach the crossmember in a few strokes instead of a dozen.
  • The swivel saddle self-centres on the diff housing instead of walking off the curve of it.

Cons: Performance Tool publishes its own minimum height inconsistently — NAPA quotes 3-1/2 inches in one place and 3-5/8 in another. Irrelevant on a truck this tall, but it tells you something about the documentation. It is also heavy steel, so it lives in the garage, not in the bed on a trail day.

Buy it if you want one jack that will still be right after you lift the truck. Check the current price.

2. BIG RED T83006 Torin 3-Ton — best budget

The default answer in half the TacomaWorld jack threads, and for a stock truck it is genuinely enough. The listing is aimed explicitly at SUVs and extended-height trucks, and with the supplied second saddle it reaches roughly 20.9 inches.

  • Clears 20 inches with the extra saddle fitted, unusual at this price.
  • Widely stocked, so seal kits and handles are easy to find.

Cons: quality control. Walmart’s listing for the same jack carries 4.4 out of 5 across 52 reviews, and the one and two-star reviews describe a missing saddle, a missing handle and a unit that arrived visibly used. Check the box contents before you need it. The extra saddle is also a stacked part, less rigid than a jack reaching 20 inches on its own arc.

Buy it if your Tacoma is stock or mildly lifted and you want the job done for the least money. Check the current price.

3. Arcan A20019 / ALJ3T 3-Ton Aluminium — best premium

A 3-ton aluminium jack at about 56 lb against roughly 90 for comparable steel. On most vehicles that is a luxury. On a Tacoma it is closer to a feature, because Tacomas get driven to trailheads and 56 lb is a weight you will actually put in the bed.

  • Around a third lighter than steel, the difference between a jack that travels and one that does not.
  • Quick-rise dual pump and a clear step up in build quality — Home Depot’s listing for the sibling A20018 carries 4.6 out of 5 across 113 reviews.

Cons: it tops out at 18 inches, fine for a stock truck and marginal for a lifted one on 33s — if yours is already lifted, buy the W1645. Arcan also sells near-identical A20018 and A20019 variants, so read the listing title rather than trusting the photo.

Buy it if your truck is near-stock and you want to carry the jack. Check the current price.

4. BIG RED T46002A double-locking stands — do not skip these

A pair of double-locking stands working from 15.4 to 23.8 inches. Nobody should be under a Tacoma held up by hydraulics.

  • Double locking: a ratchet pawl plus a safety pin, not a pawl alone.
  • The height range covers a lifted Tacoma’s frame rail, where most 3-ton stands run out near 16 inches.
  • Cheap enough to buy two pairs, the right number if you ever want all four wheels off.

Cons: the 6-ton rating is marketing as far as a Tacoma is concerned — you are buying height, not capacity. More practically, 15.4 inches is a tall minimum: lift from the crossmember so both front wheels rise together and you will clear it, but corner-jack a stock truck and the stand may not go under. BIG RED also quotes different height ranges across its own listings, so measure first.

Buy them if you are getting under the truck at all. Check the current price.

What actually matters when choosing a jack for a mid-size truck

Maximum lift height, first and last. This decides whether the tool works, and listings bury it. Stock Tacoma: 16 to 17 inches. Lifted on 33s: 19 minimum. Measure your frame rail height and add four inches for suspension droop.

Saddle shape. The rear lift point is the curved bottom of the differential housing, and a flat steel saddle wants to slide off it. A swivelling or cupped saddle, or a cheap rubber jack pad, fixes that permanently and protects the crossmember coating too.

Weight, if the truck leaves the driveway. This is the Tacoma-specific one. Aluminium costs more and lifts less high, but 56 lb is portable and 90 lb is not. Decide whether the jack is a garage tool or a trail tool first.

Stands are not optional. Budget for them in the same order. A jack lifts; a stand stops the truck landing on you.

FAQ

Where do you put a floor jack on a Toyota Tacoma?

The service manual gives the centre of the front crossmember and the centre of the rear differential. On trucks with the OEM or TRD skid plate, the front point is the small protrusion poking through the rear of the plate — there is a crossmember directly behind it, and you do not need to remove the plate.

What size floor jack do I need for a Tacoma?

Three tons, though not for the capacity. The heaviest Tacoma is 5,410 lb and lifting one end loads the jack with roughly 3,250 lb, which even a 2-ton jack covers. Buy three tons because those jacks are built taller.

Can I use a low profile floor jack on a lifted Tacoma?

Only if its maximum lift height is 19 inches or more. “Low profile” describes the minimum height, the spec a lifted Tacoma cares least about. Plenty of low-profile jacks stop near 15 inches at the top, which will not raise a lifted truck’s wheel off the ground.

Is it safe to jack a Tacoma by the lower control arm?

For a quick wheel swap, yes. For getting underneath, no — you cannot fit a stand under the control arm, so you would be trusting hydraulics to hold the truck. Lift at the crossmember and put stands on the frame rails instead.

Where do the jack stands go on a Tacoma?

Front: the frame rails just ahead of the transmission crossmember. Rear: under the axle, either at the centre housing or just inboard of the U-bolt plates. With castellated tops, make sure the frame sits between two peaks, not on one — the front frame points are nearly flat.

Verdict

For most Tacoma owners the Performance Tool W1645 is the right jack: 20.5 inches of lift works on a stock truck today and still works after you lift it. On a budget the BIG RED T83006 reaches nearly as high for less, as long as you check the box contents when it arrives. Whichever you pick, buy the stands too and lift from the crossmember and the diff exactly where Toyota says to.

Related guides

0 comment

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More